Glass touch keypad  and dual frequency RFID access control for EM4102 / 4100/4200 and ISO14443 compatible transponders  Full metal housing with concentrated double reading field through the LED bar and solid PIN code keypad  The use of plastic on the housing could almost be dispensed with.  Potted waterproof, suitable for outdoor areas  Multifunction with PIN code and RFID multi-protocol reader  Standalone function with relay output  Reading function connected to Wiegand connection for evaluation units such as Sboard access controllers and SC3000NT. The relay switching then takes place inside, so attempts at sabotage on the wall reader are ineffective. Technical details: PIN code and RFID reader full metal housing Glass keypad Color: cappuccino black Operating mode: standalone or reader (Wiegand) Dual frequency 125 khz and 13.56 Mhz RFID chip types 125KHz: HID prox, EM4200, EM4102 UID RFID chip types 13.56MHz: ISO 14443 Output format: Wiegand 26 / 34bit Housing: waterproof encapsulated IP65 LED and beep can be switched off Power supply: 12V DC, 50mA Dimensions: 170 x 83 x 26mm Download instruction manual: sKey2 instruction manual.pdf

RFID and code / waterproof / 2,000 people Access control system with integrated RFID reader antenna for contactless transponder Solid steel housing, vandal and tamper-proof Waterproof IP68 sealed 2,000 memory places (people)Transponder only or Code only or Transponder + Code Individual transponders also erased if lost Controller and integrated active antenna · - Use as a standalone device (default)· - Use as a pure controller (also for antennas (LEGIC, ISO14443, Hitag, etc.)· - Use antenna as possible Wiegand26 External door opener button can be connectedTamper switch in the housingConnection for door contactFor doors, gates, garages, shutters, etc.Potential free relay output 00-99 seconds adjustable (change)Switching time of the alarm output (sabotage) 0-3 minutes adjustableFail-safe EEPROM memory powerNo PC connectionblue backlit keypadIntegrated LEDs and beeper Reading distance: up to 6cmDimensions: 128x82x28mm Weight: ca.700gPower supply: 12V-24V DC or AC voltageCurrent consumption: approx 40mA Transponder type: Universal 125kHz (EM4102 or compatible) including interface: Wiegand 26 bit in / outincluding 2 programming cards for fast learning of transpondersInstallation and operating instructions Manual  Optional AccessoriesTags, Cards, FobsReader (W1-C is indoor mounted)Controller (W1-C is outdoor mounted as Reader)Power SuppliesLocker & Strikes

Glass touch keypad  and dual frequency RFID access control for EM4102 / 4100/4200 and ISO14443 compatible transponders  Full metal housing with concentrated double reading field through the LED bar and solid PIN code keypad  The use of plastic on the housing could almost be dispensed with.  Potted waterproof, suitable for outdoor areas  Multifunction with PIN code and RFID multi-protocol reader  Standalone function with relay output  Reading function connected to Wiegand connection for evaluation units such as Sboard access controllers and SC3000NT. The relay switching then takes place inside, so attempts at sabotage on the wall reader are ineffective. Technical details: PIN code and RFID reader full metal housing Glass keypad Color: cappuccino black Operating mode: standalone or reader (Wiegand) Dual frequency 125 khz and 13.56 Mhz RFID chip types 125KHz: HID prox, EM4200, EM4102 UID RFID chip types 13.56MHz: ISO 14443 Output format: Wiegand 26 / 34bit Housing: waterproof encapsulated IP65 LED and beep can be switched off Power supply: 12V DC, 50mA Dimensions: 160 x 45 x 26mm Download instruction manual: sKey2 instruction manual.pdf

Protective Case Rain cover / Screen Closed on all sides, including rubber seal for rough surfaceswith 2 cable bushings, Holes must be drilled individually Material: Plastic Color: Black Dimensions HxWxD: 150x104x90mm

Ruggedized PIN code and dual frequency RFID access control for EM4102 / 4100/4200 and ISO14443 compatible transponders  Full metal housing with concentrated double reading field through the LED bar and solid PIN code keypad  The use of plastic on the housing could almost be dispensed with.  Potted waterproof, suitable for outdoor areas  Multifunction with PIN code and RFID multi-protocol reader  Standalone function with relay output  Reading function connected to Wiegand connection for evaluation units such as Sboard access controllers and SC3000NT. The relay switching then takes place inside, so attempts at sabotage on the wall reader are ineffective. Technical details: PIN code and RFID reader full metal Color: cappuccino black Operating mode: standalone or reader (Wiegand) Dual frequency 125 khz and 13.56 Mhz RFID chip types 125KHz: HID prox, EM4200, EM4102 UID RFID chip types 13.56MHz: ISO 14443 Output format: Wiegand 26 / 34bit Housing: waterproof encapsulated IP65 LED and beep can be switched off Power supply: 12V DC, 50mA Dimensions: 170 x 83 x 26mm Download instruction manual: sKey2 instruction manual.pdf

High-quality key safe with various access options The weatherproof metal D3 key safe can be opened with a fingerprint, PIN code, smartphone app or RFID transponder. It can be fixed to the wall next to the door or hung up on the doorknob or railing or similar using steel brackets. A so-called 5-minute code can be assigned remotely, for example to give holiday guests access to the keys to the holiday apartment or holiday home. You generate a unique 9-digit PIN code via the smartphone app, which you can then announce to your holiday guests by phone or send it by SMS, Whatsapp or email. This code is deleted again after 5 minutes and is then ineffective. Technical characteristics: - Zinc alloy weatherproof housing- Supports RFID transponder 13.56MHz ISO14443A- Capacitive fingerprint sensor with low power consumption- Configuration via smartphone app Tuya- Door opening with fingerprint or transponder or PIN code or via Bluetooth - Power failure safe EEPROM memory - Backlit sensor field with button tones (can be switched off)- English voice announcement integrated (can be switched off) Specification:Material: zinc alloyBattery operation: 4x1.5V AAA (not included)Emergency power supply via USBStorage space for transponders/PIN codes: 150 usersStorage space fingerprints: 100 usersWorking temperature: -25°C to 55°CDimensions: 122x72x52mm Download: German assembly and operating instructions as PDF

RFID Zutrittssystem / wasserdicht IP65 / Farbe: schwarzZutrittskontrollsystem mit integrierter RFID Leseantenne für berührungslose Transponder 2000 Speicherplätze für Transponder (Personen) Einzelne Transponder auch bei  Verlust löschbar Standalone Gerät Externer Türöffnertaster anschließbar Sabotagekontakt im Gehäuse (lichtempfindlicher Sensor) Für Türen, Schranken, Tiefgaragen, Rollläden, etc potentialfreier Relaisausgang von 00 – 99 Sekunden einstellbar (Wechsler) oder als Dauerkontakt (AN-AUS-AN) für Schaltvorgänge, EMA, o.ä. die LED leuchtet dauerhaft grün solange der Dauerkontakt AN ist und rot wenn er AUS ist Stromausfallsicherer EEPROM Speicher Kein PC-Anschluß LED Leiste und Buzzer integriert Betriebs-LED abschaltbar Buzzer abschaltbar Leseabstand: bis zu 10cm Maße: 102x48x20mm Gewicht: 170g Einsatztemperatur: -40°C bis 60°C Stromversorgung: 12V Gleichspannung (9-18V) Stromaufnahme: ca. <40mA Belastung Relaiskontakt 2A Lesbarer Transpondertyp: ISO14443, kompatibel zu MIFARE® Classic 1k UID (4byte) inkl. zwei Masterkarten für schnelles Einlernen bzw. Löschen inkl. Infrarot Programmiergerät für alle Änderungen, Einstellungen (Passwortschutz 6 stellig) Englische Montage- und Bedienungsanleitung Deutsche Montage- und Bedienungsanleitung als PDF PDF Anleitung Optionales Zubehör Installationsleitung Meterware Transponder Netzteile Türöffner

Transponder Codeschloss mit RFIDRFID und Code / 1000 Personen Lesegerät mit integrierter RFID Leseantenne für berührungslose Transpondermassives Stahlgehäuse, mattiert, Vandalen- und Sabotagegeschützt1000 Speicherplätze (Personen)Nur Transponder, nur Code oder Transponder + CodeCode jetzt auch ohne Transponder anzulegenEinzelne Transponder auch bei  Verlust löschbarExterner Türöffnertaster anschließbarSabotagekontakt im GehäuseAnschluß für TürkontaktFür Türen, Schranken, Tiefgaragen, Rollläden, etcÖffnungsrelais von 1 – 99 Sekunden einstellbaroder Dauerschaltung für Licht- oder SchaltfunktionenSchaltzeit des Alarmausgangs (Sabotage) von 1 - 3 Minuten einstellbarStromausfallsicherer EEPROM SpeicherKein PC-Anschlußblau hinterleuchtetes TastenfeldLEDs und Beeper intergriertLeseabstand: bis 6cmTemperaturbereich: -40°C bis 60°CMaße:128x82x28mmGewicht: ca.500gStromversorgung: 12V Gleichspannung (8-14V)Stromaufnahme: ca. 20mABelastung Relais: max 3000mATranspondertyp: Universal 125kHz (EM4102 oder kompatibel) Deutsche Montage- und Bedienungsanleitung  Anleitung   Optionales Zubehör Installationsleitung Meterware Wetterschutzdach Transponder Netzteile Türöffner Magnetkontakt   

Sebury touch wideStand alone access systemCan be used as a complete device with integrated memory and relay outputoras a tamper-proof variant as a pure reader in connection with a door controller- Elegant and robust aluminum housing- Waterproof IP65- Illuminated touch keyboard and RFID reader for contactless transponders- 2000 memory locations for keyboard codes and transponders- Adjustable: code or transponder / code and transponder / only transponder- additional data output for professional applications: Wiegand 26-37 bit- Sabotage contact in the housing- Integrated LEDs and beeper- Acoustic alarm in the event of sabotage- alarm output- integrated changeover relay- Switching as a pulse 1-99 seconds- or as permanent ON-OFF-ON-OFF for switching functions- Bell button led out directly (internal resistance approx. 80 Ohm) only for electronic gong (max. 100mA)  or via doorbell decoder- Multi-user function, 2-10 people must identify themselves before the door is opened.- Switching as a single system or as an anti-pass-back with two readers for one door- Reading distance transponder: up to 3-10cm- Dimensions sTouch-w: 125x83x22mm- Power supply: 12V-24V DC voltage- Current: 35mA- Temperature range: -40 ° C to 60 ° C- Operating display: multifunction display (can be switched off)- Keyboard lighting: white (can be switched off or automatic when approaching)- Key tones (can be switched off)Readable transponder types:125 kHz (HID-Prox, EM4100, EM4102, EM4200 or compatible) Unique / Universal Scope of delivery:- External unit / Access Host sTouch Standalone wide- Manager cards (learning and deletion cards)- Small and fastening material- Instructions (English) print- Instructions (German) as PDFEnglish manualOperating instructions German Optional accessoriesInstallation cable by the meterTransponder EM or HIDPower supplyDoor openerControllerElectronic doorbell

Fingerprint / Fingerprint Reader and RFID Readerfor contactless universal transponderssolid waterproof metal housing IP663000 memory locations (1000 fingerprints, 2000 transponders)Fingerprint or transponder can open the doorDeletion even in the absence or loss of the tag or fingerprintController and Wiegand interface integratedUse as stand alone device (standard)Can be used as Wiegand Reader (sabotage-proof with controller in the safe area)Lock function possibleExternal door release button can be connectedSabotage contact in housingConnection for door contactFor doors, barriers, underground garages, roller shutters, etc.Relay output adjustable from 01 - 99 seconds (operating current or quiescent current)or continuous operation ON-OFF-OFF-OFF....Switching time of the alarm output (sabotage) adjustable from 1 - 3 minutesPower Fail-safe EEPROM memoryNo PC connection neededRed backlit sensor fieldLEDs and beeper integratedRead distance transponder: up to 6cmFinger sensor resolution: 500 DPIReading time: < 1 sec.Indentification time: < 1 sec.FAR: < 0,01%FRR: < 0,1%Dimensions: 128x48x26mmWeight: approx. 400gPower supply: 12V DC voltage stabilizedPower consumption quiescent: approx. 45mATemperature range: -30°C to 60°COutput load: max 2ARFID type: Universal 125kHz (EM4102 or compatible)incl. interface: Wiegand 26bit to 44bit adjustableincl. programming deviceincl. learning and cancellation cardsAssembly and Operating Instructions as PDFOptional accessoriesInstallation cableRFID card and fobsPower suppliesDoor openerAccess ControllerorController Compact

Sebury sKey wideStand alone access control systemISO14443 Can be used as a complete unit with integrated memory and relay outputoras tamper-resistant variant as a mere reader in conjunction with a door controller- Elegant and robust aluminum housing- Waterproof IP65- Illuminated Metal Keypad and RFID reader for contactless transponder- 2000 memory locations for key codes and transponders- Adjustable : code or transponder / code and transponder / transponder only- Additional data output for professional applications : Wiegand 26-37 bits- Tamper switch in the housing- LEDs and beeper integrated- Audible alarm if tampering- Alarm output- Integrated change-over relay- Circuit as pulse 1-99 seconds- Or as a continuous circuit ON-OFF - ON-OFF for switching functions- Bell button directly led out ( internal resistance of about 80 ohms) for electronic Gong ( max. 10mA )  or Doorbell decoder- Multi-user function , 2-10 persons must identify themselves before the door is opened.- Circuit as a single unit or as an anti -passback with two readers for one door- Transponder reading distance : up to 3 -10cm- Dimensions sKey -w : 125x83x22mm- Power supply: 12V -24V DC- Current: 35mA- Temperature range : -40 ° C to 60 ° C- Status display : multi-function display (can be deactivated )- Keyboard Backlight : white, On or Off , or Auto ( the 1st press ON , 30 sec OFF)- Keypad tones (can be disabled )Or use as Wiegand reader in conjunction with a door controller- Transponder data is transferred- Keyboard signals can be set as 4bit , 8bit or as a virtual card number- 26bit to 37bit adjustable WiegandmodusReadable transponder types :13.56MhzISO14443 1k, 4k, 4byte oder 7byteScope of delivery:- Outdoor unit / Access host sKey standalone wide- Manager Cards ( learning and delete card )- Small and fixing material- Manual (english) Print- Manual ( German ) as PDFManual DownloadOptional AccessoriesInstallation cable by meter Power SupplyISO14443 TAGsDoor OpenerController Network Controller Compact Doorbell decoder  

 RFID und Code / wasserdicht / 2 RelaisausgängeLesegerät mit integrierter RFID Leseantenne für berührungslose Transpondermassives Stahlgehäuse, mattiert, Vandalen- und SabotagegeschütztWasserdicht vergossen IP68Gesamt 2100 Speicherplätze 2000 Speicherplätze für Relais 1 und 100 Speicherplätze für Relais 2   Nur Transponder, nur Code oder Transponder + Code Codelänge 4-8 stellig  Einzelne Transponder auch bei  Verlust löschbar   Externer Türöffnertaster anschließbar   Sabotagekontakt im Gehäuse Anschluß für Türkontakt   Für Türen, Schranken, Tiefgaragen, Rollläden, etc Zwei Relaisausgänge (Impuls oder Statisch) Öffnungsrelais von 1 – 99 Sekunden einstellbar oder als bistabiles Relais (Dauerschaltung)Relais 2 ist auch als Klingeltaster nutzbar (Taste #) Schaltzeit des Alarmausgangs (Sabotage) von 1 - 3 Minuten einstellbar Stromausfallsicherer EEPROM Speicherinkl. Wiegand Schnittstelle 26-37bitinkl. Programmierkarten für schnelles Einlernen / Löschen(Blockspeicherung) mit sortierten TranspondernErste UID Nummer und Stückzahl eingeben, fertig (z.B. 500 St. in wenigen Sekunden) Kein PC-Anschluß blau hinterleuchtetes Tastenfeld LEDs und Beeper integriert Tastentöne abschaltbarHintergrundbeleuchtung abschaltbarBlinkende Betriebs LED abschaltbar Leseabstand: bis 6cm Maße:128x82x28mm Gewicht: ca.600g Stromversorgung: 12-24V Gleichspannungoder 12-18V Wechselspannung Stromaufnahme: ca. 25mA Belastung Relais: max. 2A Transpondertyp: Universal 125kHz (EM4102 oder kompatibel)und / oder HID Prox   Deutsche und englische Montage- und Bedienungsanleitung   Anleitung     Optionales Zubehör Installationsleitung Meterware Transponder Netzteile Türöffner Magnetkontakt

Access control system with an integrated RFID reader antenna for RFID Tags, Cards and Key fobs· NEW VERSION 2012· The flashing LED operation can be disabled by the programmer· Waterproof IP68 sealed· 10000 presets for transponder (people)· Individual transponders also at loss erasable· - Use as a standalone device (default)· - Use as a pure controller (also for antennas (Legic, ISO14443, Hitag, etc.)· - Use as Wiegand26 antenna possible· - The input and output circuit having two possible W2· - Lock function with two possible W2· - Antipassback W2 with two possibleConnected · External door opener button· Tamper switch in housing· Connector for door contact· For doors, gates, garages, shutters, etc.· 12V switch output 00 to 99 seconds adjustable (open-circuit or closed-circuit)· Switching time of the alarm output (sabotage) from 1 - 3 minutes· Power failure Secure EEPROM memory· Access time when full: <15ms· No PC connection needed· Multi-color LED bar and integrated signal transmitter· Reading distance: up to 10cm· Dimensions: 103x48x23mm· Weight: 122g· Operating temperature: -20 ° C to 60 ° C· Power supply: 12V DC (10-14V)· Current consumption: <15mA· Load outputs: max 20A (short circuit)· Transponder Type: Universal 125kHz (EM4102 or compatible)· Wiegand interface including integrated 26-bit (in / out)· Including two pre-programmed master cards for fast learning or delete· Including infrared programmer for any changes settings (password protection 6-8 digits)· German installation and operating instructionsIndicator: LED flashes red (can be disabled)Optional AccessoriesTagsReader (The W2 is mounted as a controller in the indoor area)Power SuppliesRelay (for  your own application)

Sabotage Secure Access Control System / 1,000 people Reader and evaluation unit be mounted separately, 5 wire connection, max. 100m consisting of:          controller sBoard          Active Antenna A30a          Programming Card Set          Design Keychain K694 Owner's Manual (German) wiring variants Manual (english)

RFID access control system / waterproof IP65Color: WhiteAccess control system with integrated RFID reader antenna for contactless RFID tags 2000 memory slots for tags (people) Individual tags in case of loss erasable Stand-alone deviceExternal door opener button can be connected Tamper switch in the housing (light-sensitive sensor) For doors, gates, garages, shutters, etc Potential-free relay output 00-99 seconds adjustable (change)Or as a permanent contact (ON-OFF-ON) for switching operations, EMA, etc.Power Fail-safe EEPROM memoryNo PC connection Integrated tri-color LED bar and buzzer Power LED switched off Buzzer can be switched off Reading distance: up to 10cm Dimensions: 102x48x20mmWeight: 170gWorking temperature: -40 ° C to 60 ° CPower supply: 12V DC (9-18V) Current consumption: <40mA Switch Rating 2A RFID Tags: Universal 125kHz (EM4102 or compatible) and HID ProximityIncluding two master cards for fast learning or deletion Including infrared programmer for all changes settings (password protection 6 digits) English installation and operating instructions

RFID and Code / waterproof / 2 relay outputs Reader with an integrated RFID reader antenna for contactless RFID tags, cards, labels, fobs Solid steel casing, matt, vandal and tamper-proof Waterproof IP68 sealedTotal 1200 memory locations1100 memory locations for relay 1and100 memory locations for relay 2Transponders only or  Code only or Tag + Code4-6 digit code lengthIndividual transponders deletable if lostExternal door opener button can be connectedTamper switch in the housingConnection for door contactFor doors, gates, garages, shutters, etc.Two relay outputsOpening relay from 01 - 99 seconds adjustableor as a bistable relay (maintained)Switching time of the alarm output (sabotage) 1-3 minutes adjustableFail-safe EEPROM memory powerNo PC connectionblue backlit keypadIntergrated LED and beeperKey tones switched off Reading distance: up to 6cmDimensions: 135x58x26mmWeight: ca.600gPower supply: 12-24V DC or AC voltageCurrent consumption: approx 60mALoad relay: max. 2ATransponder type: Universal 125kHz (EM4102 or compatible) English and German Installation and operating instructions   Optional Accessories Tags, Cards, Fobs Reader (W1-C is indoor mounted) Controller (W1-C is outdoor mounted as Reader) Power Supplies Locker & Strikes       at 240V         bei 240V► Zur Anzeige alternativer Übersetzungen klicken   Ziehen Sie zum Ändern der Reihenfolge mit gedrückter Umschalttaste.  

Code lock with integrated RFID antenna in the solid metal housing. The device is sealed in waterproof and thus easily mounted outdoors and can be used. RFID and code / 2000 people Reader with integrated RFID reader antenna for contactless EM4102 tags solid steel case, matte finish, vandals - and sabotage safe Waterproof IP68 Bell push button (internal approx. 80 ohms) only for electronic bells (max. 100mA) 2000 people Only tag, only code or transponder + code mode Lost tags can be deleted External door strike can be connected Tamper contact in the housing Connection for door contact For doors, barriers, parking garages, shutters, etc Opening relay from 1-99 seconds adjustable Switching time of 1-3 minutes adjustable alarm output (sabotage) Power failure safe EEPROM memory No PC connection required, management directly on the device blue backlit keypad Integrate LEDs and beeper incl. 26bit Wiegand output RFID reading distance: up to 6 cm Temperature range:-40 ° C to 60 ° C Dimensions: 118x56x20mm Weight: ca. 450 g Power supply: 12V DC Power consumption: approx. 40mA Load relay: max 3000mA at 12V DC RFID type: Universal 125 kHz (EM4102 or compatible) Installation - and operating instructions Optional accessories:Installation cableTCP-IP controllerorCompact controllerCompatible Tags, Cards, Key Fobs, Label

RFID and code / waterproof / 2,000 people Access control system with integrated RFID reader antenna for contactless RFID tags, cards, labels and fobs Solid steel housing, vandal and tamper-proof Waterproof IP68 sealed 2,000 memory places (people)Transponder only or Code only or RFID + Code Individual transponders also erased if lost Controller and integrated active antenna · - Use as a standalone device (default)· - Use in controller mode (also for antennas (LEGIC, ISO14443, Hitag, etc.)· - Use antenna as possible Wiegand26 External door opener button can be connectedTamper switch in the housingConnection for door contactFor doors, gates, garages, shutters, etc.Potential free relay output 00-99 seconds adjustable (change)Switching time of the alarm output (sabotage) 0-3 minutes adjustableFail-safe EEPROM memory powerNo PC connectionblue backlit keypadIntegrated LEDs and beeper Reading distance: up to 6cmDimensions: 135x58x26mmWeight: ca.700gPower supply: 12V-24V DC or AC voltageCurrent consumption: approx 40mA Transponder type: Universal 125kHz (EM4102 or compatible) including interface: Wiegand 26 bit in / outincluding 2 programming cards for fast learning of transpondersInstallation and operating instructions Manual Optional Accessories Tags, Cards, Fobs Reader (W1-C is indoor mounted) Controller (W1-C is outdoor mounted as Reader) Power Supplies Locker & Strikes      

RFID access control system for hidden installationmounting ready version with RFID antennaThe antenna wiring can  be extended for inwall mounting orbehind materials other than metal to hide.The controller board is installed in the room (appartment, cabinet ...), and controls the door or alarm system etc.· 1000 RFID Tags, Cards ... (people) can be stored in the controller board· Use as a standalone unit · External door opener button is connectable· For doors, gates, garages, shutters, etc.· Potential-Free Relay Contact· Switching time  1 second or 5 seconds· Power failure Secure EEPROM memory· No PC connection is needed· 3 LEDs and integrated signal transmitter· Reading distance: up to 10cm· Dimensions board: 90x50x17mm· Distance from mounting holes: 83x43mm· Antenna Dimensions: 42x30mm· Operating temperature: -20 ° C to 50 ° C.· Power supply: 12V DC (9-13V)· Current consumption: <60mA· Switch Rating: 2A max· Transponder Type: Universal 125kHz (EM4102 or compatible)· Including two pre-programmed master cards for fast learning or delete· English manual Manual Optional Accessories Transponder  

Robust fingerprint and dual frequency RFID access control for EM4102/4100/4200 and ISO14443 compatible transponders The sPress2 is a robust fingerprint and RFID access control in a solid and waterproof full metal housing. The patented dual frequency RFID reading antenna is located behind the integrated LED bar. Authorized access is gained by placing your finger on the fingerprint sensor or by holding the transponder RFID card or key fob in front of the integrated RFID reader. The sPress2 can be configured as a standalone device for switching the integrated relay or as a reading device for connection to external access control evaluation units.Technical characteristics - Transponder with 125kHz EM & 13.56MHz ISO1443 chip compatible - waterproof zinc alloy case, - Support 125KHz EM&HID card and 13.56MHz ISO14443A at the same time - Optical fingerprint sensor with low power consumption - Configuration with infrared remote control - Can be set as reading mode, single door mode, interlock mode or demo mode. - The output format can be set by the user. - Support 5 methods including card, fingerprint and multi-cards to open the door. - Supports Super Open Card (fingerprint) operation. - Door opening with fingerprint or transponder - Deletion even if the transponder is absent or lost - NO, NC, COM relay potential-free (suitable for doors, barriers, underground car parks, roller shutters, etc.) - Integrated Wiegand interface · Input/output switching with two sPress2 possible · Lock function with two sPress2 possible - Tamper contact in the housing - Connection for door contact for door monitoring - External door release button can be connected - Switching time adjustable from 50ms to 999s - Permanent switching can be activated - Power failure safe EEPROM memory - Red backlit sensor field - Integrated LEDs and beeper - Transponder reading distance: up to 6cm - Fingerprint reading time : < 1 sec. - Fingerprint identification time: < 1 sec. - Power supply: 12V DC stabilized Specification: Material: zinc alloy Input voltage: DC10~14V No-load current: ≤50mA Card reader type: 125 kHz: EM/HID 13.56 MHz: Mifare/CPU/NFC (ISO14443A) Card capacity: 20000 user cards, 21 admin cards Fingerprint capacity: 219 users, 21 admin cards Reading card distance: 125KHz: ≤5cm 13.56MHz: ≤2cm Output Format: Card: wiegand 26-66 bit (HID card output wiegand 26-66 automatically.) Working Temperature: -20~60℃ Working humidity: 0 ~ 95% (no condensation) Product Dimension: 170*83*35mm including programming device including learning and erasing cards Download: German assembly and operating instructions as PDF Optional accessories Installation cable sold by the metre transponder power supplies door opener Network access controller (high security, thanks to tamper-proof internal evaluation unit/controller) or Compact controller (high security, thanks to tamper-proof internal evaluation unit/controller)

Sebury sKey smallStand alone access control systemCan be used as a complete unit with integrated memory and relay outputoras tamper-resistant variant as a mere reader in conjunction with a door controller- Elegant and robust aluminum housing- Waterproof IP65- Illuminated Metal Keypad and RFID reader for contactless transponder- 2000 memory locations for key codes and transponders- Adjustable : code or transponder / code and transponder / transponder only- Additional data output for professional applications : Wiegand 26-37 bits- Tamper switch in the housing- LEDs and beeper integrated- Audible alarm if tampering- Alarm output- Integrated change-over relay- Circuit as pulse 1-99 seconds- Or as a continuous circuit ON-OFF - ON-OFF for switching functions- Bell button directly led out ( internal resistance of about 80 ohms) for electronic Gong ( max. 10mA )  or Doorbell decoder- Multi-user function , 2-10 persons must identify themselves before the door is opened.- Circuit as a single unit or as an anti -passback with two readers for one door- Transponder reading distance : up to 3 -10cm- Dimensions sKey -s: 159x43x22mm- Power supply: 12V -24V DC- Current: 35mA- Temperature range : -40 ° C to 60 ° C- Status display : multi-function display (can be deactivated )- Keyboard Backlight : white, On or Off , or Auto ( the 1st press ON , 30 sec OFF)- Keypad tones (can be disabled )Or use as Wiegand reader in conjunction with a door controller- Transponder data is transferred- Keyboard signals can be set as 4bit , 8bit or as a virtual card number- 26bit to 37bit adjustable WiegandmodusReadable transponder types :125 kHz ( HID Prox , EM4100 , EM4102 , EM4200 or compatible) Unique / UniversalScope of delivery:- Outdoor unit / Access host sKey standalone small- Manager Cards ( learning and delete card )- Small and fixing material- Manual (english) Print- Manual ( German ) as PDFManual DownloadInstallation cable by meterTag's EM or HIDDoor OpenerController NetworkController CompactDoorbell decoder

· Compact fingerprint access control system · Modern design · Solid aluminum housing · As a complete stand-alone device · Use or as a reader for external controller · Front waterproof · Mounting plate with grommet not waterproof · Fail-safe EEPROM memory · For up to 1000 people · Energy saving function · Touch button with integrated LED status indicator · Cover contact (tamper) · Direct 12V switch output for door strike, magnetic holder, etc. · Connection for external opening buttons · Wiegand 26bit data output for door controller · Infrared remote control for storing and specific deletion of memory locations TÖ opening time, etc. Input voltage DC 12-24V DC Standby power consumption <10mA Current consumption read operation <80mA Maximum current 3A Switching output Resolution: 450 dpi Identification time: <1sec. FAR: <0.0000256% FRR: <0.0198% dimensions 120x71x25mm Net weight: 353g Weight including packaging and accessories 480g Temperature range -20 ° C to 50 ° C Humidity 20% - 95% non-condensing Memory: 1000 fingerprints   Optional AccessoriesInstallation cable by meterTags's: EM4102Door OpenerController Network Controller Compact

RFID and code / 2000 persons Access control system with integrated RFID reading antenna for contactless transponderssolid steel housing, protected against vandalism and sabotageWeatherproof seal 2000 memory locations (persons) Only transponder, only code or transponder + code Individual transponders can be deleted even if lost Integrated controller and active antenna Use as stand-alone device (standard) Use as Wiegand26 antenna possible External door release button can be connected Sabotage contact in the housing Connection for door contact For doors, barriers, underground garages, roller shutters, etc. Potential-free relay output adjustable from 00 - 99 seconds (change-over contact) Alarm output switching time (sabotage) adjustable from 0 - 3 minutes Power fail-safe EEPROM memory No PC connection Bell button for up to 100mA Blue backlit keypad Integrated LEDs and beeper Read distance: up to 6cm Dimensions:154x43x20mm Weight: approx.500g Power supply: 12V DC Power consumption: approx. 30mA Transponder type: 13.56 Mhz ISO14443 ® 1k, 4k, 4byte UID incl. interface: Wiegand 26 bit out German installation and operating instructions Optional Accessories Tags, Cards, Fobs Reader (W1-C is indoor mounted) Controller (W1-C is outdoor mounted as Reader) Power Supplies Locker & Strikes      

RFID access control system / waterproof IP65Color: WhiteAccess control system with integrated RFID reader antenna for contactless RFID tags 2000 memory slots for tags (people) Individual tags in case of loss erasable Stand-alone deviceExternal door opener button can be connected Tamper switch in the housing (light-sensitive sensor) For doors, gates, garages, shutters, etc Potential-free relay output 00-99 seconds adjustable (change)Or as a permanent contact (ON-OFF-ON) for switching operations, EMA, etc.Power Fail-safe EEPROM memoryNo PC connection Integrated tri-color LED bar and buzzer Power LED switched off Buzzer can be switched off Reading distance: up to 10cm Dimensions: 102x48x20mmWeight: 170gWorking temperature: -40 ° C to 60 ° CPower supply: 12V DC (9-18V) Current consumption: <40mA Switch Rating 2A RFID Tags: Universal 125kHz (EM4102 or compatible) and HID ProximityIncluding two master cards for fast learning or deletion Including infrared programmer for all changes settings (password protection 6 digits) English installation and operating instructions